Loading...
Lock care guide

Van lock servicing: how to maintain your van's locks

Why van locks wear out, which lubricant to use, how often to apply it, and what's involved when a lock is professionally serviced. Written with the engineers who design, test and fit ProtectAVan security.

Free

Lock Health Check

A check-up that gets your locks ready for the winter months. Cold, wet weather is hardest on locks, so our engineers inspect each one for wear, clean it out and lubricate it before the temperature drops.

  • Inspected for wear on the pins and keyway
  • Cleaned and lubricated
  • Advice if a lock needs more work
Book a health check →
Full Service

Full Lock Service

A complete check of the lock, in the same way a car service is a complete check of the car. The lock is taken apart, every part is inspected, worn parts are replaced, and it's rebuilt to work with your existing key.

  • All internal components removed and checked
  • New springs, and new pins where worn
  • Rebuilt or remade to match your key
Book a full service →
Photo: engineer lubricating a van rear-door lock cylinder
A ProtectAVan engineer lubricating a rear-door cylinder lock with silicone PTFE spray.

Key takeaways

  • Lock servicing keeps a lock lubricated, reduces wear and helps it keep operating at proper capacity.
  • The pins and keyway wear first. Over time the key and pins wear down together.
  • Use a silicone-based lubricant with PTFE. Avoid white grease and graphite.
  • Lubricate every 6 weeks in summer and every 3–6 weeks in winter.
  • A worn lock can usually be rebuilt to work with your existing key.
  • The same care applies to most other locks, including house door locks, garages and padlocks.

Why do van locks need servicing?

Van locks need servicing so they keep operating at proper capacity. Regular lubrication stops a lock drying out, keeps wear and tear to a minimum and increases its working life.

Every time a key is used, the metal parts inside the lock move against each other. When a lock is lubricated, those parts move freely. When it dries out, bare metal rubs against bare metal, which causes the lock to snag and catch. Left long enough, the pins can freeze up completely.

A silicone lubricant creates a barrier between these parts, which stops the metal from degrading.

This isn't unique to vans. Most everyday locks, including the cylinder locks on house front doors, garages, sheds and padlocks, work on the same principle of pins inside a cylinder. They wear in the same way, and they benefit from the same care.

Need a lock serviced?

Book a free Lock Health Check with our engineers. They'll inspect your locks, clean and lubricate them, and tell you if any lock needs a Full Service.

Book a service0333 444 2200

How does a van lock wear out?

Wear in a cylinder lock happens gradually, and in a predictable order.

The same pattern applies to most pin-tumbler locks, including the euro cylinders fitted to many uPVC and composite front doors at home.

  1. The pins wear first. The pins inside the cylinder take the most wear every time the key is turned.
  2. The keyway wears. The keyway, the slot the key slides into, wears along with the pins.
  3. The key and pins wear down together. Over time the key wears to match the worn pins.
  4. The lock snags and freezes up. Without lubrication, bare metal against bare metal catches, and the pins start to freeze up.
Diagram: cutaway of a cylinder lock showing pins, springs and keyway
Inside a cylinder lock. The pins and keyway are the first parts to wear.

Signs a lock needs attention

  • The key snags or catches as it goes in or turns
  • The lock feels stiff or needs force to turn
  • A slam lock or HookLock doesn't fire cleanly
  • Pins stick, or the lock stops turning in cold weather

What lubricant should you use on van locks?

Use a silicone-based lubricant that contains PTFE. Avoid white grease and graphite.

It helps to think of it like the oil change in a car service. First, WD-40 clears out any dirt and debris that has built up inside the lock, the same way old oil is drained from an engine. Then the silicone PTFE lubricant goes in, like fresh oil. It coats the pins in a protective barrier that helps all the parts move smoothly and efficiently.

TVL Lock Lubricant
Available in our shop

TVL Security Lock Care Pack

Everything you need to service your locks between visits. The pack includes a specially formulated lock lubricant and a 300 GSM microfibre cloth for regular maintenance. Suitable for your TVL Security locks, and the same routine works for the other locks around your home and business.

  • Lock lubricant for smooth operation
  • Protects against wear and corrosion
  • Reusable, washable microfibre cloth
Price£5.00
Buy now

This applies to any lock, not just the ones on your van. A house door lock, a garage lock or a padlock will all benefit from the same clean-out and lubricate routine.

The silicone lubricates the lock and acts as a repellent, so dust and debris don't build up inside it. The PTFE leaves a barrier once applied that won't dry out, and won't congeal and turn to grease. Silicone also has no freezing point, so it keeps working in cold weather. Grease, by contrast, thickens up in the cold and can clog the lock.

Van lock lubricants compared
LubricantIn cold weatherOver timeRecommended
Silicone with PTFENo freezing pointWon't dry out or congeal. Repels dust and debris.Yes
White greaseThickens and clogsCongeals and turns to greaseNo
Graphite–Congeals and turns to greaseNo

How often should you lubricate van locks?

Lubricate your van's locks every 6 weeks in summer and every 3–6 weeks in winter.

Cold, wet conditions are harder on locks, so they need attention more often through the winter months. Locks also need cleaning and re-lubricating after exposure to snowy slush or a car wash.

Outdoor locks at home, such as those on gates, sheds and garages, face the same weather and benefit from the same routine.

Recommended lubrication schedule
WhenHow oftenWhat to do
SummerEvery 6 weeksSpray with silicone PTFE lubricant
WinterEvery 3–6 weeksSpray with silicone PTFE lubricant
After slush or a car washAs soon as possibleClean with WD-40, then spray with silicone
If the lock is dirtyBefore lubricatingClean with WD-40 first, then spray PTFE in after

How to lubricate each type of van lock

The same silicone PTFE spray is used on every type of lock. What changes is where you apply it and how you work it in.

RepLock fitted to a van
RepLock. View product →

Cylinder locks

These steps also work for the cylinder lock on a house front door or back door.

  1. If the lock is dirty, clean it with WD-40 first.
  2. Spray the silicone PTFE lubricant into the lock and onto the key.
  3. Move the key in and out of the keyway a few times.
  4. Fire the lock a few times to spread the lubricant through the cylinder.
SlamLock
SlamLock. View product →

Slam locks

  1. Lubricate the cylinder in the same way as above.
  2. Spray lubricant on the back of the cam to reduce wear and tear.
HookLock 2.0
HookLock 2.0. View product →

HookLocks

  1. Lubricate the cylinder in the same way as above.
  2. Spray the same lubricant onto the hook.
  3. Fire the lock a few times to work the lubricant into the mechanism.
ArmourShell
ArmourShell. View product →

ArmourShells

  1. Lubricate the bullet lock in the same way as a cylinder lock.
  2. Check around the edge of the bullet lock, where it meets the shell. Moving back and forth over time can cause the hole in the shell to wear.

What's involved in professional lock servicing?

ProtectAVan offers two levels of lock servicing: a free Lock Health Check, and a Full Service for locks that are worn.

Lock Health Check (free)

The Lock Health Check is designed to make sure your locks are prepared for the winter months, when cold and wet weather puts the most strain on them. An engineer inspects your van's locks for wear on the pins and keyway, cleans them out with WD-40 and lubricates them with silicone PTFE spray. If a lock needs more than that, they'll explain what and why. Confirm what's included

Full Service

The Full Service is a full lock check, much like a car service. Rather than just topping up the lubricant, the engineer takes the lock apart and checks every part.

All internal components are removed from the lock. Springs are replaced, and worn pins are replaced where the wear is bad. If the chamber is worn, it's changed. If the lock has gone past repair, the whole cylinder is replaced and matched to your existing key.

What a Full Service involves, by level of wear
ConditionWhat the engineer doesYour key
Light wearInternal components removed and cleaned, new springs fittedKeep current key
Heavier wearNew pins fitted, chamber changedKeep current key
Past repairWhole cylinder replaced and remade to match your keyKeep current key. New key cut recommended.

When a new cylinder is fitted, we recommend having a new key cut, as an old key will already have worn down with the original pins.

Book a lock service

Start with a free Lock Health Check. Our engineers will tell you if any lock needs a Full Service.

Book a service0333 444 2200
About this guide

Written with the ProtectAVan engineering team. TVL designs, manufactures and fits van security, including HookLocks, ArmourShells and slam locks, from workshops in Brentwood, Loughborough and Swindon.

Frequently Asked Questions

0333 444 2200
[email protected]
Monday to Friday, 7:30am – 5pm

Everything you need to know about servicing your van's locks, from the free health check to what happens if a lock is past repair. If you cannot find what you are looking for, please reach out to our support team.

Why silicone PTFE and not white grease or graphite?–
Silicone lubricates the lock and repels dust and debris, so nothing builds up inside. PTFE leaves a barrier that won't dry out. White grease and graphite congeal and turn to grease over time, and grease thickens up in the cold, which clogs the lock. Silicone doesn't have a freezing point.
How often should I lubricate my locks?+
What's included in the free Lock Health Check?+
What happens during a Full Service?+
Will I need a new key?+
What if my lock is past repair?+
My lock is dirty, or I've been through a car wash. What should I do?+
How do I lubricate a HookLock or slam lock?+
Can I use the same lubricant on my house locks?+
Can you service ArmourShells?+
How do I book a service?+
Book a service
Four steps from booking to serviced.
1
Get in touch

Book online or call 0333 444 2200. Tell us your van and which locks are fitted.

2
We check your locks

Our engineer inspects for wear, then cleans and lubricates each lock.

3
We explain what we found

If a lock needs a full service, we'll tell you why before any work starts.

4
Back to proper capacity

Your locks are working as they should, with the key you already have.

Look after it.
Before it locks up.

Book a free Lock Health Check, or talk to the team about a full service for a worn lock.

Book a serviceCall 0333 444 2200
Monday to Friday, 7:30am to 5pm